First, we read the stickers on the back of the TV, where for each tuner (DVB-T and DVB-C), a list of countries in which, according to Philips, there is digital broadcasting (at the time of release of the TV, but if you update the firmware through them official site, then in subsequent firmware this list may change). If our country is not there, then you have to put some other from this list.
2. select - "Configuration"
3. select - "Installation"
6. select - "Digital Mode"
7. select - "Cable"
8. select - "Automatic"
9. click - "Start"
Instruction number 2
Philips 2011 TVs
1. Click on the icon - "House"
2. select - "Installation"
3. select "Channel Search"
4. select - "Reinstall channels"
5. select - "the country that is indicated on the sticker on the back" (usually France, Finland or Germany)
6. select the digital mode - “Cable (DVB-C)”
7. in the line "Network frequency" drive the frequency
8. in the line "Transfer Rate" drive
Setup takes about 5-10 minutes.
Instruction No. 3
1. In order to configure high-definition digital TV channels for the vast majority of Philips models, press the “Menu” button on the remote control, you will see the TV menu, in which you will need to select the “Configuration” section
2. Select the "Installation" tab. After clicking the “OK” button, you will move to the second menu field, then go to the “Channel Settings” tab. After clicking the “OK” button, the third part of the menu will open, where you need to select “Automatic. Installations. " Then you will see a message about updating the list of channels, click "Start"
3. Select “Reinstall Channels”
4. In the Country section, you must select Finland, if the proposed list does not have this country, select Germany
5. Since you are connecting to digital television via the DVB-C cable network, you must select “Cable”
6. Before you start searching for channels, select “Settings” to manually correct the search parameters
7. Set the manual baud rate. In the tab, we manually change the baud rate from the control panel to the desired one. In some TV models, the flow rate is indicated in the tab “Symbol 1”, “Symbol 2” leave 0.
8. Now set the manual mode of the network frequency and from the control panel enter the network frequency
9. After clicking the tab is ready, you will again be taken to the start channel menu, now you can start scanning
10. If you did everything correctly and saved all the changed parameters, then during the search you will find channels.
D101-0
Cause:
The TV did not manage to transfer to the CAM-module service information available in the stream of the TV signal
Decision:
Switch to the encrypted channel and wait 3-5 minutes until the TV completely transmits all the service information from the TV signal to the CAM module.
Correct setting of the date and time on the TV can also help.
E006-4, 104-2, E106-9, E106-9, E04-4
or "Status is undefined"
- smart card was not inserted correctly
- smart card contacts dirty
- smart card malfunction
- non-MTS smart card used
- smart card does not fit this set of equipment
- defective prefix or card reader in the prefix
- reinstall smart card
- clean smart card contacts (without using harsh cleaning materials and detergents)
E101-4, E107-4
- The card did not receive a deactivation command.
- A command to activate this card has not been sent.
- MTS smart card is installed in a third-party receiver, i.e. not a receiver or cam-module MTS (E107-4)
Decision:
Request technical activation by phone
E016-4, E16, E16-4
- insufficient funds on the balance of the personal account
- lack of subscription to a specific channel
Top up your account or switch to another channel if an error occurs while trying to view an unpaid channel package
E106-9
- Used smart card not from MTS
- Factory defect smart card
Use the smart card that was bundled with the MTS prefix / cam module. If you use an MTS smart card, call the technical support phone.
E030-4, E120-4
on the TV to which the TV module is connected, the date and time are incorrectly set.
Set the exact time and date on the TV using the instructions in the TV. If this does not resolve the errors, disconnect the TV module from the TV and reconnect it.
E019-4
tV with cam-module did not turn on for a long time
Check if the device has a smart card, make sure the cable is connected to the TV, then leave the TV turned on for several hours or call technical support with a request for reactivation.
E133-4
E48-32
- Update software version
- Reset to factory settings and re-search channels
- Try removing and reinstalling the SMART card.
E107-4
Smart card is not activated. Request technical support to activate the equipment.
E52-32
no satellite signal
Check the quality of all cable connections for mechanical damage. Check the integrity of the converter as well as the antenna settings. After troubleshooting, reset the set-top box to the factory settings and start a new channel search.
No error code or error D101-0
The inscription on the TV screen: CI + ERROR: Host Certificate Invalid-Expiried, Please Tune to DTV service - 16 (Сl + ERROR: invalid Host certificate, expired, please switch to another program)
To solve the problem, reset the TV or set-top box to the factory settings and start a new channel search. If this error appears on the console, you may need to update the software.
Host error, expired, switch to another program
This error occurs when using the cam module. To correct it, set the correct time on the TV.
Modern TVs need to be pre-configured: network connection, channel search. In general, the procedure is intuitive: you just have to trust the prompts of the system. However, some users still have difficulties. Below we provide a detailed manual for Philips TVs.
If the box from the device is preserved, then it should have a brief specification indicating support for the DVB-T2 format. Similar information can be found in the instruction manual. If the documentation is missing, then it’s worth inspect the rear of the TV. The interface labeled DigitalInput indicates that the model supports digital TV.
Important! Devices released before 1998 do not work with the DVB-T2 format. Until 2004, the equipment was equipped with digital outputs only partially: these were expensive televisions with a diagonal of more than 40 inches. Everywhere, the format began to be introduced after 2005.
That's all the difficulties of setting up digital channels on a Philips TV when it has the functions of a modern Smart TV. Perhaps the following video will help many users in making such settings:
Wanting to connect digital television, many people turn to companies that provide these services. These companies offer everyone to set up free digital TV channels for a certain amount. Most customers agree to this, and do not even know that this is not necessary.
You can set up DTV on almost any TV. The only thing required for this is the presence of a tuner, which can be built-in or external. It all depends on the company of your TV and its model. Most modern TVs have this property. The main thing is that it was a device of foreign manufacture and was released no earlier than 2005-2006.
Philips TVs are quite popular in Russia. This is due to their reliability, quality, prevalence and relatively low cost. Today we will talk about how to set up digital TV for those who are also devices from this company.
Channel settings on TVs until 2011
The interface of many Philips TVs is different. However, the general scheme for installing digital television on them is as follows:
If during the execution of these steps your TV starts asking for a password, you will need to enter 0000, 1111 or 1234. These are standard passwords that will give you access to certain options.
Modern TVs Philips
More modern models are configured almost the same, but there are some features.
To set up your modern Philips model, you need:
If you choose a quick scan, then you will need:
- Set the frequency difference to 8 MHz;
- Disable analog channels, if you have already configured them, click "Finish" and start the search.
If you want to perform a full scan, then:
- In network frequency mode, select “Manual”;
- Next, you should set QAM - 256 and frequency - 298.00;
- After that, you will also need to turn on or off the search for analog channels and proceed to search.
If everything was done right, your TV will begin broadcasting the free digital channels available in your area.
Programs
