How to solve a problem with slow copying data on a USB flash drive? Consider the common causes of this problem and talk about how to solve it.

1. Flashley performance

If everything is in order with the computer, the culprit of the slow process of transferring files to the USB flash drive, respectively, is the latter. Budgetary flash drives, as a rule, can not boast of impressive speed recording speed. And speed of 5-7 MB / s interface uSB connections 2.0 may be commonplace for those. You can test the flash drive data recording speed using Windows Speed \u200b\u200bTesting Programs hard disks, in particular, through a popular utility. More than that Speeds that show the tests of the flash drive, you should not expect from it in practice.

2. Computer USB ports

Acquired on a faster data recording USB 3.0 flash drive will work in the same way as USB 2.0 flash drive, if only this interface is supported by a computer, and USB 3.0 is not. The USB flash drive will limit the speed of the port. In order to obtain the USB 3.0 interface performance when copying data, the USB ports of the computer must be equipped with them. The same concerns the situation when the USB 3.0 or 2.0 drive is connected to the USB port 1.0. The flash drive is connected to a low-speed USB 1.0 port, Windows, as a rule, immediately informs the system notice: they say, this device can work faster if it connects to the USB 2.0 port.

If the data is slowly copied to a USB flash drive, which is connected to the USB port on the front panel of the PC housing, you can test its speed in connecting to USB ports. motherboard Behind the hull. It may be so that the front panel of the case is derived uSB ports 2.0 or 1.0, while the ports of the motherboard provide interfaces.

Like USB ports that limit your capabilities of data recording, to cut the copying speed of files can USB extension cords. If the USB extension supplies USB 2.0 interface, it is its limit throughput Specifies the speed of the USB 3.0 flash drive interface and the computer's USB port.

3. Weak computer stuffing

On the old or budget models of computers, a slow recording of data on a flash drive can be due to a weak hardware stuffing, in particular, by a small volume. random access memory or slow hard disk. In this case, only a computer upgrade will help.

4. Drivers

Slow copying data on the USB flash drive can be due to incorrectly installed uSB drivers. In this case, you can either update the motherboard drivers, or reinstall USB controller drivers. Updating motherboard drivers can be done manually by downloading the desired installers from the official website of the board or laptop, and you can charge this case to special programs - driver installation managers. Among those: Drivermax, Auslogics Driver Updater, SlimDRIVERS, Advanced Driver Updater, etc.

To reinstall USB controller drivers, open the dispatcher windows devices, we reveal the branch "USB controllers" and using the "Delete" option in the context menu of each of the List devices, delete its driver.

USB controller drivers will be installed automatically.

5. BIOS settings

In some cases, slow data recording on a flash drive may be due to limiting the speed of USB ports in the BIOS settings. Such a restriction must be searched as a rule, in the Advanced section bIOS settings "Advanced". If, in front of the "USB 2.0 Controller Mode" parameter, it is the "low-speed" value, it must be changed to "Hi-Speed".

6. How to speed up the data record on the USB flash drive software

If the cause of the problem lies in the low speed recording of the data of the flash drive itself, alas, to significantly speed up the process of copying files to it fails. Even if available has a productive computer. Software File recording speed can be increased only slightly.

If you need to copy several small files on the USB flash drive, it is better to merge them into one archive file. And put this archive file on the USB flash drive. One weighty file copied faster than the mass of small. By the way, when copying small files, even productive USB drives can "Like".

Just accelerate the transfer of files to the USB flash drive using special programsWinning W. full-time Windows copying some fraction of productivity due to its own data copying algorithms. One of these is WinMend File Copy, you can download it for free from the creators of www.winmend.com/file-copy.

WinMend File Copy has a Russian-speaking interface, supports batch copying files, buffer setting, as well as renewing data transfer from the break point.

Excellent day!

Modern USB drives are one of the most popular external data carriers. An important role in this also plays the speed of recording and reading data. However, the capacious, but slowly working flash drives are not too comfortable, so today we will tell you what methods can increase the speed of the flash drive.

The first thing to be noted is the reasons why flash drives can decrease. These include:

• nAND wear;
• inconsistency of the standards of the input and output connectors USB;
• file System Problems;
• incorrectly configured BIOS;
• viral infection.

Create a situation with worn chips, alas, it is impossible - it is best to copy data from such a flash drive, to purchase a new one and transfer information to it. It is also worth considering the origin of such a drive - flash drives from little-known manufacturers from China may be low-quality with a very short service life. The rest of the described reasons can be tried to eliminate yourself.

Method 1: Check for viral infection and its elimination

Viruses are the most common cause of a slowdown in the flash drive. Most of the types of malicious software creates a bunch of small hidden files on a flash drive, which is why the speed of access to normal data is significantly reduced. To deal with the problem once and for all, it is worth cleaning a flash drive from existing viruses and secure from subsequent infection.

Method 2: Connecting a flash drive to a speedy port

Now there is still a common standard USB 1.1, accepted almost 20 years ago. It provides a very low data transfer rate, which seems that the flash drive works slowly. As a rule, Windows reports that the drive is connected to a slow connector.

A message about slow work can also be obtained by connecting a flash drive uSB standard 3.0 to the most common Yusb 2.0. In this case, the recommendations are the same. If all the connectors on your PC or Laptop of Standard 2.0, then the only solution to the problem will be a hardware update. However, some motherboards (both desktop and laptop) do not support YUSB 3.0 at the hardware level.

Method 3: File System Change

Method 4: Changing flash drive settings

In modern Windows variants, the USB drive is running in quick removal mode, which gives certain advantages to the data saving, but also slows down the speed of access to them. Mode can be switched.

The only drawback of this method is the dependence of the flash drive from "Safe extraction". However, for most users to use this option to turn off rather norm, so that this disadvantage can be neglected.

Method 5: Change BIOS configuration

Flash drives exist for a long time, and modern PCs and laptops are not always compatible with old flash drives. Bios has an appropriate setting, which is useless for modern drives, and only slows access to them. Disable this setting follows:

We looked at the most common causes of falling the speed of flash drives and solving this problem. However, if you still have options, we will be happy to hear them in the comments.

When the user starts copying files to the USB flash drive, it can sometimes notice that the copy speed is rather low. In modern versions of Windows, it is usually shown in the form of a graph and a numeric value. I usually reaches up to 6-7 MB / s, and often jumps down, then up. During problems, the speed may not be higher than 600 Kb / s, or somewhere in these values. For a normal flash drive, this indicator is unacceptable.

Let's look at the reasons for this phenomenon and try to figure out the solution of the problem.

Properties flash drive

When using a flash drive, purchased for 200 rubles, you will not see high speeds of reading and writing. This suggests that any port on the computer you did not use -, then the increase may not happen. You can try to use the program and check the maximum speed of the flash drive. Using it, you can test hard drives and SSDs. The results will show exactly the maximum speed, which can differ much from the one that is written on the box. It is not worth more to count.

Using high-speed USB ports

If there is a couple of USB ports 3.0 on your laptop, then they must be used. Usually, if you connect the device to a low-speed port, the system reports notice. If you have connected a USB flash drive, which has the capabilities of USB 3.0 to port 2.0, then you should not expect rapid speeds.

In case of desktop computerYou can try to connect a flash drive to the rear panel of the system unit.

Also, limit the speed of copying can also extension. Than it is longer, the smaller the speed.

Low computer characteristics

If you still use old equipment, which is 7-8 years old, and the characteristics of the RAM and hard disk are waiting for the best, then in increasing the speed of reading the recording on the flash drive will also help the PC upgrade.

Curves drivers

If you just inserted a new flash drive, the installation of the controller drivers will immediately begin. If they rose not as necessary, then expect a slow reading speed. In this case, the only option will be.

You still need to update the system board drivers if you have not done this yet. You can download you need from the official website of your board manufacturer, or using special programs, such as Drivermax, Driverpack Solution or SlimDRIVERS.

To reinstall USB controller drivers, you need to go to the Device Manager. This can be done as follows: Press the right mouse button on the Start menu and knock the corresponding item. You can still press Win + R and enter the command devmgmt.msc..

We find the "USB Controllers" section, open it and remove the driver of the following devices - "Root USB concentrator" and "Expandable host controller ...".

After deletion, click the "Action" tab at the top and select the item "Update Equipment Configuration".

Remote drivers must be installed automatically.

Programs to increase the speed of reading flash drives

In the presence of good computer With productivity, but with a flash drive, which has low copying indicators, you can hardly increase the speed by using utilities.

If you copy a lot of small files, so that they are copied many times faster need to be placed in the archive.

A slightly increase the copying process will help the program. Free and simple interface, it will help you to raise the copy speed. If when copying has failed, you can continue with the interrupted place.

That's it. Maybe you have more answers to the question why the files on the USB flash drive are slowly copied?

How to solve a problem with slow copying data on a USB flash drive?

Consider the common causes of this problem and talk about how to solve it.

1. Flashley performance

If everything is in order with the computer, the culprit of the slow process of transferring files to the USB flash drive, respectively, is the latter. Budgetary flash drives, as a rule, can not boast of impressive speed recording speed. And the speed of 5-7 MB / s with the USB 2.0 connection interface for those may be common. You can test the flash drive data recording speed using Windows-programs for testing hard disk speeds, in particular, by means of the popular CrystalDiskMark utility. More at the speed that the tests of the flash drive show, you should not expect from it in practice.

2. Computer USB ports

Acquired on a faster data recording USB 3.0 flash drive will work in the same way as USB 2.0 flash drive, if only this interface is supported by a computer, and USB 3.0 is not. The USB flash drive will limit the speed of the port. In order to obtain the USB 3.0 interface performance when copying data, the USB ports of the computer must be equipped with them. The same concerns the situation when the USB 3.0 or 2.0 drive is connected to the USB port 1.0. The flash drive is connected to a low-speed USB 1.0 port, Windows, as a rule, immediately informs the system notice: they say, this device can work faster if it connects to the USB 2.0 port.

If the data is slowly copied to a flash drive, which is connected to the USB port on the front panel of the PC housing, it is possible to test its speed in connecting to the USB ports of the motherboard from the back of the case. It may be that the USB 2.0 or 1.0 ports are displayed on the front panel of the housing panel, while the ports of the motherboard provide USB 3.0 or 2.0 interfaces.

Like USB ports that limit your capabilities of data recording, to cut the copying speed of files can USB extension cords. If the USB extension supplies USB 2.0 interface, it will limit the speed of the USB 3.0 interface and USB ports of the computer with its limit bandwidth.

3. Weak computer stuffing

On old or budget models of computers, a slow data record on a flash drive can be due to a weak hardware stuffing, in particular, a small amount of RAM or a slow hard disk. In this case, only a computer upgrade will help.

4. Drivers

Slow copying data on a flash drive can be due correctly installed drivers USB. In this case, you can either update the motherboard drivers, or reinstall USB controller drivers. Updating motherboard drivers can be done manually by downloading the desired installers from the official website of the board or laptop, and you can charge this case to special programs - driver installation managers. Among those: Drivermax, Auslogics Driver Updater, SlimDRIVERS, Advanced Driver Updater, etc.

To reinstall USB drivers, open Windows Device Manager, open the branch "USB controllers" and using the "Delete" option in the context menu of each of the list devices, delete its driver.

USB controller drivers will be installed automatically.

5. BIOS settings

In some cases, slow data recording on a flash drive may be due to limiting the speed of USB ports in the BIOS settings. Such a restriction must be searched, as a rule, in the Advanced Bios Advanced Settings section. If, in front of the "USB 2.0 Controller Mode" parameter, it is the "low-speed" value, it must be changed to "Hi-Speed".

6. How to speed up the data record on the USB flash drive software

If the cause of the problem lies in the low speed recording of the data of the flash drive itself, alas, to significantly speed up the process of copying files to it fails. Even if available has a productive computer. Software File recording speed can be increased only slightly.

If you need to copy several small files on the USB flash drive, it is better to merge them into one archive file. And put this archive file on the USB flash drive. One weighty file copied faster than the mass of small. By the way, when copying small files, even productive USB drives can "Like".

A slightly speeding up the transfer of files to the USB flash drive using special programs that benefit from the staff of copying Windows some share of productivity at the expense of your own data copying algorithms. One of these is WinMend File Copy, you can download it for free from the creators of www.winmend.com/file-copy.

WinMend File Copy has a Russian-speaking interface, supports batch copying files, buffer setting, as well as renewing data transfer from the break point.

Question: The process of copying on the USB flash drive drops to 0

When copying a flash card with a USB 2.0 connector, an unknown thing happens through a laptop with USB 3.0 connectors. What does this happens with all the flash drive 2.0. The copying process begins normally, but copying not a large volume, the speed drops to 0 and then the copying does not continue. Formatted flash drive to all formats, turned on / off caching, tried everything file managers and programs for copying. I repeat what happens not with all flash drives 2.0, I have three of them. Two work fine, with 3 here are such troubles and with some flash drives for which they asked to throw something.

Answer: Novito., firewood on USB everything delete and reboot

Question: in office The network on one computer disappears the Internet when copying files from the second computer to the third one. So does not happen?

There is a small office network, about 10 computers and one as a file sharing. All on Win 7.

Unexpectedly on one of the computers (let's call it conditional BUT) the Internet is cut off, while internal network continues to work without problems. Network icon without exclamation mark. Ping to Yandex writes "exceeded interval ...", but occasionally pass packets.

After long experiments it turns out that if on another computer (let's call it B.) or the third (let's call it IN) Copy something from the file sharing (let's call it G.), then in the process of copying on the computer BUT Disappears the Internet. Once the copy is completed, the Internet appears.
At the same time, if you copy something from the file sharing on other computers ( D, e, f, s, and...), then the Internet on the computer and does not disappear.

All computers are combined with uncontrollable gigabit switches.

Manages this all old reliable router / firewall.
Some of the computers are connected directly to the GS116 switch, and the part to the second GS608 score, which, in turn, is connected to the first.
The network scheme is attached.

Immediately respond to possible assumptions: IP and Mac addresses on computers are naturally different. On some IP are set to manually, on some machines are automatically. Network 192.168.1.1-254

All computers are connected by cables, not by Wi-Fi.

Another nuance. But maybe it is normal. Ping in the network grows up to 20 ms if you download something from a "file sharing".

Answer:

Message from Novoao.

Suddenly on one of the computers (let's call it conditional a)

Update the motherboard driver and network card or temporarily replace each other network cardnot to torment users. Call wiring or prohibit vitua couple On both sides, it can wire somewhere overcrole (stretch a new twisted pair or connect from another PC)

Question: After starting the game GPU loaded by 99%, the game begins to produce 5fps and even after the completion of the GPU does not fall

After starting the game GPU loaded by 99%, the game begins to issue 5fps and even after the process of the GPU process does not fall, without the Internet GPU 0%
Win7.
i5-3470.
GT 630 1GB.

Answer: The Pasib helped it seems no longer loading so!

Question: List of flash drive programs

- Chipgenius v2.72. (2009-02-25) - utility for information on all connected USB devices. Shows VID & PID values. There is a built-in base for which the model and manufacturer of the controller is determined.
- Checkudisk v5.0. - Utility for information about all connected USB devices.
Shows IDVENDOR and IDPRODUCT values \u200b\u200bto determine the type of device controller.
And also shows speed revision, serial number Flash drive.
- USBidCheck. (USB Bench - Faraday USB Test Utility) - a program for information about all USB devices connected. Shows IDVENDOR and IDPRODUCT values \u200b\u200bto determine the type of device controller. The list by which you can define the device manufacturer - the USB.IDS.TXT file in the program folder.
- Flash Disk Utility v1.20 - program for quick and complete formatting of the flash drive, creating boot disk, compressing data and encryption password, instruction in English.
- Flashnull.- Utility for testing the performance and services of flash memory (USB-Flash, IDE-Flash, SecureDigital, MMC, MemoryStick, SmartMedia, XD, CompactFlash, etc.). List of operations performed:
- read test - check availability of each media sector (duplicates the functionality of conventional HDD tests)
- Test write - checking the possibility of recording each media sector (duplicates the functionality of most HDD tests)
- Test the safety of recorded information - checking the compliance of the recorded and read information (similar to the MemTest functionality, but for Flash drives).
- Saving the content image of the device - the sectoral saving of the entire (or part) content to the file. (Similar to DD functionality from UNIX).
- Loading an image into the device - the sectoral image entry into the device (similar to the functionality of DD from UNIX).
Instructions in Russian.
- iCREATE_IFORMAT_V1.32. - Utility for ICReate I5122 controllers, i5128, i5129. After installing the program, the working window appears and disappears, inserting the USB flash drive can format ...
- MPTOOL V2.0. (MXT6208 + A MPTOOL V2.0) - Utility to restore flash drives on the MXTronics MXT6208A controller. Helps Chinese kingstone flash drives and some sony fakes.
- Umptool v1.6.3. - Utility to restore Flash on Chipsbank CBM2090 controllers.
Perhaps it is suitable for other CBM209x series controllers.
- USB Disk Storage (HP USB Disk Storage Format Tool. v2.1.8) - utility for formatting and creating uSB boot Flash (supported by NTFS, FAT, FAT32).
- Dr. UFD v1.0.2.17 (PQI Dr.UniflashDisk 1.0.2.17) is a branded utility for low-level Flash formatting on PQI controllers. Supported models:
- Card DRIVE SERIES
- Intelligent DRIVE SERIES
- Cool DRIVE SERIES
- Traveling Disk Series.
- Ezrecover - USB Flash Recovery utility helps when the flash is defined as Security DevixE, is not determined at all or shows 0MB volume. In order for ezrecovery to see the flash drive, after starting the program and issuing an error message to remove the USB flash drive and insert it again and then all the way.
Attention! After using the program, all data on flash will not be saved.
- Format V30112. - Branded utility for flash drives PQI. Allows you to format, manage partitions, create hidden and passionate sections.

- JetFlash Recoverytool v1.0.20- Utility to restore (repair) USB Flash Transcend.
Solving a problem when formatting JetFlash when the error appears "No Jetflash Found!"
1. You must enable the display of hidden files (Folder properties - View - Show hidden files and folders).
2. Run the MFormat utility.
3. Go to the TEMP folder in the catalog of your account (For example: Documents and Settings - Leon - Local Settings - Temp).
4. If everything is done correctly in Temp'e, the JFAPP folder should appear, in which the JFormat.exe file will be found.
5. Running jformat.exe We're bypassed the message "No JetFlash Found!".
- MFormat - Branded TRANSCEND utility for JetFlash formatting

HP USB Disk Storage Format Tool 2.1.8 Freeware
---
A utility for formatting flash cards and flash drives (supported by NTFS and FAT), as well as to create boot DOS discs. Works with devices through uSB port 2.0.

LLFSetup.2.36.1181
This utility allows you to convert file System Flashki without data loss.

Answer: some paid programs:
ACTIVE UNDELETE 7.3.003 SE
Allows you to restore files that were randomly or deliberately removed, lost due to failure or falling system, disk format or viral attack effects. Supported File Systems: NTFS, FAT32, FAT16, NTFS5, NTFS + EFS; works with all operating windows systems, as well as replaceable drives different types and species: SD, CF, SmartMedia, Memory Stick, Zip, USB Flash Drive, USB Hard Drives and many others.
The main features of the program:
Creating a bootable CD / DVD with a "lightweight" version of Windows Vista (WINPE 2.0) to recover data when loading cannot hard disk or connect the damaged disk to another computer;
restore remote files with IDE / ATA / SATA / SCSI drives;
restore files with removable media (SmartMedia, Secure Digital, MemoryStick, etc.);
Support for external zip drives and USB drives;
restore files from remote, damaged and formatted sections;
support for large (more than 500 GB) hard drives;
Support FAT, FAT16, FAT32, NTFS, NTFS5, NTFS + EFS file systems;
support for long and localized file names;
restoration of compressed, fragmented and encrypted files on NTFS sections;
scanning sections damaged by viruses or with damaged MBR;
Advanced file search by name / date / size / attribute / mask;
visual representation of the file / directory restability;
the ability to preview the recoverable files;
Built-in Hex editor for viewing / editing any disk sector;
Two types of disk scan - fast and complete;
Restore files to any available space (incl. network Disk);
the ability to connect to remote computers and scanning / creating disk / recovery images remotely;
support for hardware and software RAID arrays;
Simple and friendly interface;
Support Drag and Drop;
Full interactive reference system.

GetDataback for Fat and NTFS 4.00.2
One of the leading and well-known, not only in narrow circles, tools to restore data from various carriers. German program GetDataback, with its inherent reliability and accuracy, will restore the data, even if the partition table and boot sector Damaged, folders and files are destroyed, as a result of a viral attack, random formatting, overwriting, deletion, etc. Even if low-level formatting is produced or if the system itself is already "doesn't see", GetDataback will still return your data anyway.
It is used simple and absolutely safe for files, in the "read-copy only" mode of the three-step individually adjustable recovery system. Works both with long names and with non-standard sets of Unicode characters, such as Japanese, Chinese, Korean, Russian, Greek languages, etc. GetDataback returns data from hard drives (IDE, SCSI, SATA), dynamic disks, USB disks, floppy disks, disk, sections, ZIP / JAZ disks, CF, Smart Media, SD Flash cards, USB Flash Drive and iPod disks. Produced separately for FAT and NTFS.
This program exists in two versions - GetDataback Fat and GetDataback NTFS, each of which only works with the said file system type. The program interface is a typical step-by-step "master". At the first stage, you have to choose a recovery type - restore remote files, data recovery as a result of formatting / deleting a partition, recovery "chaotic lined" data. In the next step, you specify a section or disk area for search, and GetDataback starts scanning. The process is not fruitful, so the advantages of the program should include the ability to save intermediate results at any stage of recovery. The program will show you it found in the specified area sections. Finally, after selecting the partition, GetDataback will list all the files found and allow you to restore the selected.
GetDataback allows data recovery both on the computer on which the program is installed and on the remote - for example, on any of the local network computers.
Supported work with the following types of media:
Hard drives with IDE, SCSI, SATA interfaces
USB drives
Firewire drives
Separate sections
Dynamic discs
Diets
Disc images
ZIP / JAZ drives
Cards Compact Flash, Smart Media, Secure Digital
USB Flash drives, iPod discs

R-Studio 5.1.130005 RUS
R-Studio is a group of reliable, efficient and cost-effective utilities to restore data from hard drives, as well as other devices - such as CD, DVD, disks, disks, ZIP disks and flash memory devices (Compact Flash Card, Memory Sticks) . Based on the latest unique information analysis technology on media and data processing, R-Studio is the most exhaustive software solution Recovery utilities available for FAT12 / 16/32, NTFS, NTFS5 file systems (created or modified in Windows 2000 / XP / 2003 / Vista), EXT2FS / EXT3FS (Linux File Systems), as well as UFS1 / UFS2 (File File FreeBSD / OpenBSD / NETBSD / SOLARIS system). The program functions both on local and on remote computers On the network, even if the disk partitions were formatted, damaged or deleted. Convenient in setting the parameters The program interface gives the user absolute control over the data recovery process.
R-Studio utilities restore files
* Deleted out of the basket or when the basket was cleaned;
* Deleted viral attack or computer power failure;
* After the file sections were reformatted, even in the section with another file system;
* When the partition structure on the hard disk has been changed or damaged. In this case, with r-STUDIO programs You can scan hDD, find a remote or damaged partition, and then restore the data from the found partition.
* With hard drives, on which there is a large number of damaged sectors. The R-Studio Recovery Program may first copy the information and create an image of a whole disk or part of it, and then work with the image file saved on another carrier, as with original disc. This is especially useful and effectively when the number of damaged sectors on the disk is constantly growing, and it is necessary to immediately save the remaining information.
New features R-Studio
Various methods Representations of data. For aid R-Studio Discount data can be presented in accordance with the actual structure of folders / files, as well as ordered by expansion, creation / last access / change time.
Streamlining files. Found files and folders can be ordered by their source structure, extension, creation / change time.
Extensible list of known types of files. The user can add new signatures to the list of files of known types.
Support mass recovery files. Recovery parameters can be applied to all recoverable files.
Find / mark the dialog box. R-Studio allows you to find and mark all the files corresponding to the parameters specified in the Find / Mark dialog box.
Additional features Hex Editor. Added the ability to view files in ANSI and Unicode encodings.
Support for new file systems. In addition to FAT / NTFS / EXTFS2 / EXTFS3 / UFS1 / UFS2 file systems, the new version of R-Studio supports HFS and HFS + file systems, developed by Apple Computer for use on computers with Mac OS.
Apple computers support. A new version R-STUDIO EMERGENCY can be running with CD on Intel compatible Macintosh computers.
Support Big Indian Variant UFS.
APM support. APM (Apple PARTITION MAP) - partition scheme used to determine the low-level data organization on disks formatted on Macintosh RLT computers.
Support for various rare RAID configurations. It is possible to explicitly specify such parameters as the size and order of the unit, offset and even the number of alternating blocks. There is a visual editor to create a certain order of the block.
R-Studio Technical Portable Added to R-Studio Technical Package. The portable version starts from the USB storage device.
Support compressed format. When creating a disk image or part it can be compressed and divided into several files to save on CD / DVD / Flash Drive or on FAT16 / FAT32.
Features R-Studio: 5.0
Support RAID 6, including Reed-Solomon and Vertical XOR. Support user configurations RAID 6.
Advanced copying of objects. In addition to direct copying of any object apparently in the Drives panel, a managed copying of sections and hard drives with dimensions and displacements is available.
Support for 64 and 32 bit versions of Windows. Under the 64-bit Windows R-Studio can overcome a limitation of 3 GB for a 32-bit application and use the full physical memory installed in a computer from a 64-bit Windows. It greatly improves the work of the program, especially when scanning disks with a large volume.

UFS Explorer Professional Recovery 3.15.3
The UFS Explorer software product is a powerful, comprehensive and easy-to-use product to access data and data recovery. It is created to provide simple way receiving your information.
With UFS Explorer, you can in "read only" mode (not destructive) access:
Sections of various OS: Windows, Linux, BSD, Unix, Solaris, MacOS, Snapos, NetWare (Fat12, Fat16, Fat32, NTFS, NTFS5, EXT2, EXT3, Reiserfs, XFS, UFS, UFS2, HFS, HFS +, UDF, ISO9660, NWFS);
Various media: All Windows PATA / SATA disks, SCSI disks, USB drives (flash cards, digital devices, external hard drives), CD / DVD, FLOPPY and devices like them, RAID arrays (even disassembled);
Images of discs of these media, as well as virtual disks created by the virtualization products of various vendors: VMware, Microsoft, Parallels.
Together with its alternative method of accessing information, UFS Explorer contains functions to restore lost files after removal, formatting, recycling disk to sections, viral attack.
The application is suitable even to professionals in data recovery and gives a complete toolkit to access data and restore information.
Key concepts:
Universal access: UFS Explorer is a product that allows not to take care of the actual location of the data. It supports fast and secure access To most disks, including SCSI / SATA / PATA, USB drives, RAID arrays, VMware virtual disks, Microsoft Virtual PC, Parallels Workstation, BOCHS and conventional images of discs and partitions.
Built-in support for most file systems makes data recovery very simple!

Data Recovery.
Several recovery levels: UFS Explorer allows you to quickly get the required data.
UFS Explorer products use several recovery levels: from direct reading the file system to advanced heuristic analysis methods. This allows you to get the result as efficiently as possible and in the shortest possible time.
If you have several OS on your computer - the UFS Explorer makes information available regardless of the actual location and with the usual speed!
Lost or deleted file? Did the file system be damaged? UFS Explorer will help restore your data.
Data Recovery.
Recovery over the network: You are organized with a wide computer Network? Of course, you care about reducing the risks of data loss at workstations of your employees, and in the case of loss - to restore it in the shortest possible time.
Using UFS Explorer you can minimize downtime, quickly restoring information on the network instead of calling a specialist in place of work.
Files undelete.
Fast Undelete instead of long scans: deleted file? UFS Explorer supports fast recovery C FAT and NTFS.
This gives a very fast file recovery method if it is removed from the "basket" or removed without a "basket".
If you have a digital camera or an MP3 player, defined by Windows as a disk, with UFS Explorer you can restore remote files Without difficult work right from the device and copy to your local disk.
Raid Recovery.
Recovery RAID: The RAID array does not work because of the disk failure or controller? Unable to collect an array after reconfiguration? UFS Explorer can help in your RAID 0, RAID 5, RAID 1 + 0 virtual assembly or simple JBOD RAID (or combinations) and restore information from there.
UFS Explorer can automatically reconstruct some RAID: you only need to specify discs or images of discs on which RAID is located; Also supported manually assembly mode.
Unlike some similar products, UFS Explorer collects virtually, so you can proceed with recovery immediately, without creating any large intermediate files.
Files undelete.
Access in batch mode: Do you want to configure copy files on a schedule with an alternative file system or media? Would you like to periodically copy a blocked log file for analysis? UFS Explorer has a version for command line - Batch Edition.
Based on specially trained scripts, it can open any supported file system and copy any files from there.
The Batch edition works from the command line, as well as can be built into the packet task.

FlashBoot 1.4.0.157
One of the best utilities to create a boot disk to USB Flash Drive. The program is made in the form of a convenient step by step wizard offering 9 possible options Creating a boot disk: PE BUILDER-based disk or copies of the existing boot CD, creating a disc using a floppy disk or based on disk images, creating a password recovery alarm disk (for Windows 2000 / XP and Linux) and so on.

Question: Speckening Speed \u200b\u200bRecording and Reading Seagate ST2000DL003

good day
The problem is:
There are 2 HDDs
Both seagate ST2000DL003, bought in different time and in different stores
Used as the HD videos vault. The last time connected to the computer 1 year ago.
Now I bought a disk for 4 TB and wanted to merge all the video and the problem was discovered.
When copying speed over time, begins to fall up to 2 MB in sec. Although most of the speed is copied at 60 MB / s. Checked the recording The same speed of recording begins with 120 MB, most of the time passes on 50MB and at some point drops to 2.
As I said these are not small files. All files with a volume of more than 2 GB.
From other disks, copying is normally. I tried to format, did not help.
Firmware stand the latter.

Here is smart

Help to figure out what's the matter!
Thank you very much!

Answer: And if you try to copy with the help - what speed does it show at the beginning and at the end of copying the file?

Question: Brakes the machine when copying files

Good day!

I have a computer:

Quote:
Here is a complete report on the gland (made through Aida Business Edition):
HTML:
TXT:

He is all good, but when accessing the screw is simply terrible brakes. If, for example, copy the file in 1,5GB with C: \\ on D: \\, it starts "cheerful" (the rate first for example 30 MB / S), then copies with some jerks and as a result, the speed or in general falls to zero And then jumps up, or dangles around 3-5 Mb / s. If something big is written, then you can go drink Tea TK brakes such that it is impossible to work

Anti-virus in real time is disabled, I think it is not in cases.

I have suspicions that this is due to a specific server system Win 2012. Native to it refused. First, I tried to put in compatibility modes for a seven and eight, as a result, everything that could - manually set up via Device Manager -\u003e Right click on the element, "Update Driver Software", and pointed out the folder with firewood. Two were supplied from disc controllers, but the rest show the version of the 2006 driver, maybe this is

What to do with it? You can somehow "deceive firewood" so that they counted Win 2012 "server eight" (in fact it is it)?

upd: If you look at the properties of this ATA Channel 0, you can find this:

Quote:
freedaw., Thank you by the way for the good advice! I myself did not think about it ..

Very helpful Ment69. from the Oszone forum and enabling the AHCI driver.

The speed has ceased to "Like" and dangles between 20-30 MB / S and above hundreds, and finally stopped ladies!). And finally, you can simultaneously copy files and still do something without a slideshow

For win 8 and 2012, leave (note that for other Os-her, the keys will be different, google)

Question: Tell me what prog can you reflash the flash drive? I can not find by parameters

Please give a professional advice, how to restore the Chinese USB flash drive using the AMECO MW6208E 8208 program 1.2.1.0 090928. (or some other). It seems all the parameters of the controller and the numbers fit. But the prog does not see the flash drive. Do you enter manually, gives an error after clicking Apply. Do not understand how to use it. The USB flash drive was pulled out of the port, during copying (without a safe extraction). After this, it writes "protected from recording" and is not formatted by any program. Timed through com.strock and through the registry did not help. Had this program will help. That's how it turned On your forum. Higher! Thank you in advance. Volume -500 GB. Now the letter of the flash drive on Win7 is not determined (it is simply "disk drive). Size, no disk letters. On the computer: Administration-\u003e Computer Management -\u003e Disk Management, the disc is visible (size and written, what is working ). The XP flash drive is visible and with the letter. What I just did not do, crashes the "disk protected from the entry"! I thought about the prog in the parameters. I found it, but she doesn't see "flash drive! There is no information on the flash drive. Just format !

Answer: Thank you, I read the topic, only there are several nuances: firstly I tried my flash drive on another magnetol the same garbage. The second, I tried a 8 GB flash drive. The root of which was about 100 songs and the folder in which about 600 songs it works fine. The third I tried another flash drive (though the microspate with the adapter) is also 16 GB. and threw the same as on her and she normally works on my radio tape recorder and finally the fourth time I throw 3 folders on average 450 songs in each and when I pull it out of the laptop and immediately insert literally after a couple of seconds In the first folder, everything is fine as many songs as you need and the second and third folder are empty when I check the size of folders, then a little less than 4GB. And I check the employment of the flash drive, the properties write that it is complete

QUESTION: HEAT USB USB 3.0

Hello forum! I have such a problem: there is a Sandisc Ultra Fit 32GB USB 3.0 flash drive; She is literally a couple of days (a gift for NG17, by the way, congratulations to all !!) and when writing to it until a certain moment, the speed ~ 60MB / s, and then drops to 20-18MB / s and the flash drive becomes a fire in the literal sense when you try to pull your fingers burned down. There is still an external screw, too, 3.0 But the port block of it is certainly heats, but not so much. So the question itself is a normal phenomenon or need to look for the cause while the flash did not melt, and the drop in speed is associated with heating or not?

Answer: I have a flash drive for 2 years. When exchanging data is also quite warm, of course, hands do not burn, but the metal USB itself is rather hot becomes. Works stable. So you can exchange in the store and see, perhaps it is normal for this flash drive.

Q: Acer 5738Z (JV50-MV) freezes when reading with uSB flash drives

It hangs when reading with USB flash drives, as well as with a built-in cardrider. And B. safe mode - Reading goes fine. At least, I installed Windows from the flash drive. South a little warm. Other USB devices work normally.

Answer: Reinstalled the system. Put 32-bit. And finally found why it hangs. From the flash drive, the files are normally written only when there is no video playback! If you put on playback of video, copying from the file flash drive is suspended. The flash drive just falls off. Sometimes the computer hangs. I can not understand how video playback affects USB?

Work with android