It's hard to believe, but until recently, mobile phones were nothing more than a simple means of communication. Today, these are real multimedia centers, hiding a thousand and one entertainment in their small building. “Communication” with a mobile phone is so addictive that many cannot take a break from it even for that short time when the phone is on charge. The result is logical - the leading position among all breakdowns of mobile phones is occupied by various damage to the charging sockets. How to charge the phone battery if the charging socket is broken, you can find out from our article.

How to charge the phone if the socket is broken?

Let's make a reservation right away that in the case of a loose or broken charging socket, as in most other mobile problems, trouble is much easier to prevent than to fix. Therefore, we advise you not to forget about prevention: when using the phone in recharging mode, you must ensure that the load on the socket is minimal. Otherwise, the charger plug will serve as a kind of lever that destroys the socket from the inside. The same rule applies when removing the phone from charging - the effort to remove the plug must be directed parallel to the plane of the phone, and not at an angle to it. If trouble could not be avoided, then you can charge a phone with a broken socket using the following algorithm.

The mobile phone has become so firmly established in our lives that many no longer imagine how they could do without it. Every owner is familiar with the situation when you need to make an important call, or receive a message, and the mobile phone battery is treacherously discharged, or even worse, there is a charge, but nothing happens. How to charge the phone if the socket is broken?

Method one

This method of how to charge the phone if the socket is broken is the easiest and does not require any skills at all. True, the battery of the mobile phone will suffer and will not be able to withstand repetition. All that is required is to remove the battery and hit it hard on something hard, such as a table or stone. You will be able to make 1 or 2 calls.

Method two: a frog to help

The next way to charge a phone if the charging socket is broken is very expensive and does not justify the cost, but it is suitable if you or your loved ones have a "frog". This is a universal charger with a special slot where the mobile battery is inserted. This method has its drawbacks:

1. At its cost, the "frog" significantly exceeds the costs in comparison with the service center.
2. You will not be able to use your phone until the battery runs out.
3. Some user reviews of the device noted a battery failure during charging.

Method 3: Direct charging without using the socket

If you have some skills in working with electricity, then this method of charging the phone if the socket is broken can be done at home. Step-by-step instruction:

1. Remove the battery from your mobile phone.
2. Disconnect from the network first.
3. Remove the insulation from the wire
4. Clean up the veins. Find plus and minus.
5. Locate the correct terminals on the battery. Observe the polarity of the wires and the device itself.
6. Fix the cores, after which you can plug the plug into the outlet.

Important! This method cannot be used if you are alone. There must be someone who can help you with a possible electric shock.

Method four

The described method will tell you how to urgently charge the phone if the socket is broken. Take an ordinary knife and heat it on fire. Attach it to the battery. By increasing the temperature, the battery will recover for a short time. This method is best used only when the call is more important than the cost of the battery. Follow the rule: when heating the battery, act quickly and carefully, otherwise it may swell. Heating the battery itself will make it possible to make a call lasting about 5 minutes, but the battery will have to be replaced.

Travel way to charge your phone

The previous methods described how to charge the phone at home if the socket is broken and there is no "frog", but what if the situation turned out to be exactly the opposite: do you urgently need to call in the country or on a hike? And in this case, there is a way to make a call, unless, of course, the necessary materials are at hand. In order to make a charger yourself, you will need several metal plates, a small piece of copper wire, and salt water. If you are going on a hike, for example, you can take everything you need with you in advance in case of an emergency. The described method will be able to recharge the phone by 5%.

The plates are buried in the ground and wrapped with copper wire. The structure is watered with salt water. The charger is ready. In case iron is not available, it can be obtained as follows: metal pins are stuck into existing products, for example, lemons or apples and wrapped with wire.

Is it possible to go to extreme measures

The following methods of charging the phone, if the socket is broken and there is no “frog”, are recommended to be used only in extreme cases, they can damage the battery. Otherwise, it is better not to spare time and take the mobile phone to the service.

Do-it-yourself socket replacement or service center?

Can I fix the charging socket myself? Theoretically - yes. But do not forget about the functions that this connector performs:

1. Through the charging socket, files are transferred from the phone to the computer and vice versa. This is perhaps the most important function, besides charging the gadget, given how much important data can be stored on a memory card.
2. Through the charging socket, you can charge the phone directly from the computer using a special cord that comes with the mobile.
3. Through the charging connector, you can connect your mobile to the TV to view photos and videos.
4. Some other possibilities.

Charge your iPhone without using a charger

If you are the owner of an iPhone, then the hiking method described above will not be useful to you. Alternative sources have appeared on the market that can convert the energy of the environment into electricity. Only use them without visiting the salon will not succeed.

If you have no experience in repairing cell phones, it is better not to undertake repairs on your own, as a careless move can finally finish off your smartphone, which costs much more than the services of service centers. In addition, you can only aggravate the breakdown and the repair will cost more than the amount that could have been originally.

If the socket is OK, but there is no charging

If in order, and the phone does not charge, there may be a breakdown in the charger. In this case, you can charge your mobile phone via the USB port by connecting it to a computer or tablet.

How to choose a service center

It is best to give the phone to a branded service of the same brand as the device. Service certificates are required. View reviews of the selected service on the site.

In addition to a computer or laptop, there is a smartphone and some other mobile gadget, more and more complaints are heard that the tablet has stopped charging. Which is especially true if you or your relatives decide to save on the purchase and purchase a low-quality handicraft Chinese-made device. In this article of the site "" we will analyze the most common reasons why the tablet does not charge, does not charge, and having found the cause of the malfunction, the reader:

Or fix the damage on their own;
- or replace those elements that cause a failure in normal operation (charger, battery);
- or give the tablet to a repair service (if it is impossible to fix the breakdown at home).

1. Broken charging adapter

A broken charger is the main reason why tablet stopped charging. Understanding that the adapter has broken will not be difficult at all. To conduct the test, it is enough to connect the tablet to any other device (computer or laptop) or try another adapter with similar connectors (for example, from a phone, camcorder or camera).

If a tablet connected to the laptop's USB port starts to take charge, it is obvious that the problem is with your adapter. If the tablet is perfectly charged from the second adapter from the camera or smartphone (for example), then the reason will also be in the adapter from the tablet.

If, and you figured it out for sure with the help of an experiment, the easiest way is to purchase a new charger. For those who like to tinker with a soldering iron and a tester (multimeter), we can advise you to “ring the contacts” and solder the broken wires.

2. Broken tablet battery

If the tablet began to lose its charge very quickly even with a full battery or at all tablet stopped charging, works only when plugged into a power outlet, it can be argued that the tablet battery is covered. This fault cannot be repaired by yourself, so you will have to buy a new battery. When buying a battery in a store, we recommend that you bring a tablet with you to show it to a sales assistant and pick up an identical new battery.

Note: each battery has its own capacity, and the higher it is, the more the device works without recharging. Ask the seller to show you the most powerful battery that can hold a charge much longer than cheap Chinese fakes.

3. Loose connector for charging

If the tablet stops charging, do not rush to immediately run for a new battery to the store. Try to move the charger wire with your fingers where it enters the tablet connector. By moving the plug, you can notice instant glimpses of the charge supply to the device, which come intermittently. If this is true, then the problem lies somewhere:

In the adapter cord (loose or broken wires);
- in the tablet connector socket (loose, broken, clogged with dust or sand);
- in the tip of the adapter (contacts have come off, fasteners or latches have broken).

Fixing a broken connector at home is unrealistic. The tablet will have to be carried to a service center. On the other hand, carefully inspect the device and its sockets, it happens that dust, dirt or sand clogs in them, which also interferes with the normal charging of the tablet (especially true if small children live in the house).

4. Broken tablet

The worst case is when tablet stopped charging, lies in the problem with the "hardware", with microboards and parts inside the device. So, for example, a tablet may have a faulty cable or power controller, which cannot be fixed on its own. It turns out that if the 3 previous points do not allow you to determine the cause of the malfunction (this is not a connector, no battery, no adapter), then going to a service center will be inevitable.

Similarly, you can contact the service department, if you have even the slightest doubt about the correctness of your own diagnosis, you cannot fix the breakdown yourself. An experienced master for a very low fee will fix a broken device, advise on how to avoid breakdowns in the future.

It's hard to believe now that mobile devices were the easiest way to connect with other people. Now an ordinary mobile phone has turned into a high-speed smartphone with huge multimedia functionality, and the case has begun to store the power of a good computer inside. The use of devices is very addictive and some do not even take a break even for a short time. Such operation greatly affects charging, and constant recharging can lead to breakage of one of the phone's most important connectors. How to fix the phone charging socket if it is broken, you will learn from today's article.

Can the charging module socket be repaired?

How to fix the charging port on your phone at home? Here you need to carefully understand, then everything will work out. Inaccurate use of a mobile device very often ends in some kind of breakdown that needs to be fixed. Sometimes the failure lies in the connector for connecting the power cable. In this case, you need to find out how to fix it, and for this you should familiarize yourself with the main causes of the defect.

The main reasons for the breakdown of the device socket:

• You can spill some liquid on the device or just drop it well to disable this module.
• Constant mechanical influences deform the socket, which can make charging the gadget simply an impossible procedure - the plug will not fit into the socket or will hang out in it.
• The contact pads can also bend, which completely blocks access to electricity.

Let's talk right away about the worst - about moisture.

Contact of a mobile phone connector with moisture is the most dangerous damage. Corrosion will start a chain reaction and all neighboring components will oxidize. Such defects can also harm the dynamics, which is most often located in the lower part of the device. Also, the speaker itself gives access to moisture to get on the cable or connector. Therefore, even not heavy rain can disable your phone.

The most important thing is to assess the complexity of the damage, since not all cases allow you to do home repairs. The best option is to use the services of a qualified specialist from some service center. So you will not risk breaking your device.

Can the device be repaired at home?

Very rarely, restoration work can be carried out independently. It's best to find an alternative way to charge for a while until you decide for yourself whether to fix it yourself. While the necessary amount is being saved for repairs in the workshop, read the instructions for charging a phone with a broken socket:

• Insert the charger into your smartphone and plug it into the network.

Important! This method is relevant only for devices that have suffered from mechanical stress, and not from moisture.

• Gently move the cord and the device in different directions. You may be able to close the contact and charge the device.
• If the mobile phone nevertheless detected the presence of a charger, then it is worth fixing the position found. Books and other items can be used to set the phone so that the power continues.
• Before carrying out all these actions, it is worth making sure that the problem is in the socket, and not in the battery. Prolonged use of the phone leads to the fact that it stops holding a charge. For this case, you will have to get a new battery, and not deal with a “phantom” breakdown.
• If the matter is still in the nest, then repairs cannot be avoided here.

Important! Remember that all these manipulations can further loosen the nest, so do not apply great force during the work.

Alternative charging method

If the design of your phone allows you to remove the battery, then you can use universal charging. Such devices are called "Frog". It costs, of course, not very cheap, but sometimes you need to urgently charge your phone. This gadget has special grooves into which you need to insert and fix the battery.

But this method also has a number of obvious disadvantages:

• While charging, the smartphone will not work and you will not be able to use it until the battery is charged.
• The purchase price of the "Frog" is quite high and does not always justify its purchase.
• If the manufacturer's reputation is very questionable, then you will only harm your device.

Charge your device directly

How to fix the phone charging port? You can try to replenish the energy reserves by disconnecting the power port itself from the phone.

Important! This method is very complex and requires the user to have basic knowledge and skills in working with equipment and electricity.

The essence of the work is as follows:

1. We remove the battery from the smartphone.
2. We disconnect the charger from the socket, arm ourselves with a sharp object and remove the insulation from the wire by five centimeters.
3. Strip the wires and determine where is the plus and where is the minus.
4. Determine the polarities on the battery and connect the wires to it.
5. Fix improvised terminals and apply mains power.

Important! It is not recommended to resort to this method, as you may be injured even during charging. Do not work on bare wires if you have never done so and do not know how electrical current behaves.

Do-it-yourself repair

You need to act very carefully if you still decide to fix the phone charging socket with your own hands.

To disassemble the case and extract the nest, we need:

• A small set of screwdrivers.
• Technical tweezers (regular tweezers will do).
• Stationery knife or regular sharp.
• Soldering Station.

Now you need to do the following:

• We unscrew all the screws on which the case is attached.
• Carefully remove the cover by prying it with a clerical knife.
• We ground the soldering iron, solder the wire to the minus (device body). The second end of this wire must be brought to the body of the soldering iron itself.

Important! These measures are necessary to prevent the mobile phone from being affected by the accumulation of static electricity, which can damage parts. It would also be nice to make an antistatic wrist strap and ground it.

• Now solder all the wires from the socket. This is necessary to prevent a short circuit.
• Next, you need to remove the screws from the board that hold it. Now we have access to the microUSB connector.
• We take out the old socket, solder a new one in its place, assemble the device in the reverse order and check it for operability.

Repair of the input for charging on the phone is over! If you did everything right, then the former performance will return. We hope that in the future you will not have to face such a problem very soon, but for this you just need to carefully handle your equipment.

The mobile phone has become so firmly established in our lives that many no longer imagine how they could do without it. Every owner is familiar with the situation when you need to make an important call, or receive a message, and the mobile phone battery is treacherously discharged, or even worse, there is a charge, but nothing happens. How to charge the phone if the socket is broken?

Method one

This method of how to charge the phone if the socket is broken is the easiest and does not require any skills at all. True, the battery of the mobile phone will suffer and will not be able to withstand repetition. All that is required is to remove the battery and hit it hard on something hard, such as a table or stone. You will be able to make 1 or 2 calls.

Method two: a frog to help

The next way to charge a phone if the charging socket is broken is very expensive and does not justify the cost, but it is suitable if you or your loved ones have a "frog". This is a universal charger with a special slot where the mobile battery is inserted. This method has its drawbacks:

1. At its cost, the "frog" significantly exceeds the costs in comparison with the service center.
2. You will not be able to use your phone until the battery runs out.
3. Some user reviews of the device noted a battery failure during charging.

Method 3: Direct charging without using the socket

If you have some skills in working with electricity, then this method of charging the phone if the socket is broken can be done at home. Step-by-step instruction:

1. Remove the battery from your mobile phone.
2. Disconnect from the network first.
3. Remove the insulation from the charger wire,
4. Clean up the veins. Find plus and minus.
5. Locate the correct terminals on the battery. Observe the polarity of the wires and the device itself.
6. Fix the cores, after which you can plug the plug into the outlet.

Important! This method cannot be used if you are alone. There must be someone who can help you with a possible electric shock.

Method four

The described method will tell you how to urgently charge the phone if the socket is broken. Take an ordinary knife and heat it on fire. Attach it to the battery. By increasing the temperature, the battery will recover for a short time. This method is best used only when the call is more important than the cost of the battery. Follow the rule: when heating the battery, act quickly and carefully, otherwise it may swell. Heating the battery itself will make it possible to make a call lasting about 5 minutes, but the battery will have to be replaced.

Travel way to charge your phone

The previous methods described how to charge the phone at home if the socket is broken and there is no "frog", but what if the situation turned out to be exactly the opposite: do you urgently need to call in the country or on a hike? And in this case, there is a way to make a call, unless, of course, the necessary materials are at hand. In order to make a charger yourself, you will need several metal plates, a small piece of copper wire, and salt water. If you are going on a hike, for example, you can take everything you need with you in advance in case of an emergency. The described method will be able to recharge the phone by 5%.

The plates are buried in the ground and wrapped with copper wire. The structure is watered with salt water. The charger is ready. In case iron is not available, it can be obtained as follows: metal pins are stuck into existing products, for example, lemons or apples and wrapped with wire.

Is it possible to go to extreme measures

The following methods of charging the phone, if the socket is broken and there is no “frog”, are recommended to be used only in extreme cases, they can damage the battery. Otherwise, it is better not to spare time and take the mobile phone to the service.

Do-it-yourself socket replacement or service center?

Can I fix the charging socket myself? Theoretically - yes. But do not forget about the functions that this connector performs:

1. Through the charging socket, files are transferred from the phone to the computer and vice versa. This is perhaps the most important function, in addition to charging the gadget, given how much important data can be stored on a memory card.
2. Through the charging socket, you can charge the phone directly from the computer using a special cord that comes with the mobile.
3. Through the charging connector, you can connect your mobile to the TV to view photos and videos.
4. Some other possibilities.

Charge your iPhone without using a charger

If you are the owner of an iPhone, then the hiking method described above will not be useful to you. Alternative sources have appeared on sale that can convert environmental energy into electricity. Only use them without visiting the salon will not succeed.

If you have no experience in cell phone repair, it is better not to undertake repairs on your own, as a careless move can finally finish off your smartphone, which costs much more than the services of service centers. In addition, you can only aggravate the breakdown and the repair will cost more than the amount that could have been originally.

If the socket is OK, but there is no charging

If the socket is OK and the phone does not charge, the charger may be defective. In this case, you can charge your mobile phone via the USB port by connecting it to a computer or tablet.

How to choose a service center

It is best to give the phone to a branded service of the same brand as the device. Service certificates are required. View reviews of the selected service on the site.

How to fix the phone charging socket? How to fix a phone charging socket at home? Do not know? Let's figure it out and fix it at the same time. Are you ready? Then let's start. With inaccurate use, the power socket sometimes breaks. In this case, you should know how to fix the phone charging connector or charge it in another way.

The main reasons for the breakdown of the charging socket

You can force the connector to break if you have a habit of frequently dropping the device or spilling various drinks and other liquids on it. With constant impacts, the socket may be deformed, which will make charging the tablet impossible, since the plug simply will not fit into the socket, but may be blocked by some body part that has shifted after a strong blow. Pin connectors can also bend when connected, then your gadget will not receive energy.

Much more dangerous than damage from contact with the wet environment of the dock connector. This can damage various neighboring components, which include the polyphonic speaker, which is always located at the bottom of the device. In most cases, it is the speaker, or rather its mesh, that is the conductor of liquid and moisture to penetrate the device case to the cable and connector.

How to fix your phone charging jack at home

It is necessary to immediately indicate that it will not be possible to repair your device in this way. A broken power socket will remain so and repair cannot be avoided. This half-measure is necessary in situations where there is no required amount for repairs, but you need to use your mobile phone. Instructions on how to charge the phone if the socket is broken:

• Connect the charger to the device, plug into the network.
• Try to wiggle the cord by moving the plug up and down.
• If the battery cannot be charged because the contact has come loose, doing so may short it out.
• If the cell phone has detected the charger, try to fix this position. Try placing books or other objects under the wire so that the mobile phone can lie there overnight and the battery is charged. Before carrying out such a manipulation, make sure that the problem is really in the connector, and not the battery. When used for a long time, they have the ability to stop holding a charge. In this case, you should buy a new battery, and not deal with an allegedly damaged socket. If the matter is really in the connector, then repair is unlikely to be avoided. Keep in mind that such manipulations with the wire can further loosen the connection point or break it completely

Before carrying out such a manipulation, make sure that the problem is really in the connector, and not the battery. When used for a long time, they have the ability to stop holding a charge. In this case, you should buy a new battery, and not deal with an allegedly damaged socket. . If the matter is really in the connector, then repair is unlikely to be avoided. Keep in mind that such manipulations with the wire can further loosen the connection point or break it completely

Replacing the charging connector with a universal device

In a critical situation, when you don’t know how to charge your phone, if the socket is broken, you can use universal charging. Sometimes the device is called a “frog”, it is relatively expensive, so it’s not a fact that it’s better than giving the device for repair. This device has a special groove into which you need to insert the battery removed from the mobile. However, this method has several obvious disadvantages:

• during recharging, the smartphone is turned off, you can not use it until the battery is charged;
• the cost of the "frog" is high and sometimes does not justify the costs;
• among user reviews there are situations,
• when the charger broke the battery

If you completely broke the socket for charging your phone, charge directly

If you don't know how to change the charging socket on your phone, you can try recharging the battery by removing the need for the power socket. The method is relatively complex and requires some skills from the field of working with electricity. The bottom line is this:

• You need to remove the battery from your phone.
• Cut off the insulation from the charger wire, expose the wires (disconnect from the outlet).
• Strip the wires, determine where the plus and minus are.
• Locate the corresponding terminals on the cell phone battery.
• It is important to observe the polarity of the wires and the device. Fix the wires and plug the plug into the socket.

It is strongly not recommended to use this method if you are not 100% sure of your skills. You should not carry out manipulations when you are alone at home, there must be a person nearby who could help you with a possible electric shock. It should be borne in mind that this connection option is not normal for the battery and can lead to breakdown or premature exhaustion.

The only proven way to get rid of the problem is to put the matter in the hands of professional workers. Perhaps after being told how much it costs to fix a phone charging jack, you don't want to use any "workarounds". In modern devices, this connector still performs the function of connecting to a computer, transferring data, so its breakdown greatly reduces the functionality of the device. This is a microcircuit that cannot be repaired at home on its own. Phone repair often results in a round sum and you should be prepared for this.

In this case, it is best to contact a certified center. The ideal option would be a branded service point of the same manufacturer as your mobile. They know all the intricacies of the device of their products and will be able to provide qualified assistance to fix the breakdown. Inexperienced or inaccurate workers can aggravate the situation and lead to even greater damage to the device.

It often happens that the phone stops charging, although when you check the charging from it, it turns out that it is working. Thoughts arise - the phone is faulty. But not many people think that the reason for the lack of communication between the phone and the charger may be a banal clogging of the phone's input jack. A fairly large number of phones do not have a protective plug on the USB input jack. Since many people carry the phone in their pockets, and they accumulate rubbish in themselves over time, which imperceptibly, but surely penetrates into the phone jack.

If the phone has been worn in your pocket for a long time and has never been listed, then most likely its usb input socket is already clogged. If you're still lucky, then the phone normally charges and connects to the computer. It may be that there is a periodic loss of normal contact with charging. Well, in the worst case, the phone does not charge at all and does not connect to the computer, although everything is fine with charging and with the wire.

As soon as you start having problems with the normal charging of the phone (the phone does not charge, the charging is working), I immediately advise you to clean the USB input on your phone yourself. This is done quite simply. First, gently with a thin needle, we try to scrape out the debris from the depth of the phone's input connector. This debris can be a compressed piece of dust and lint. It is he who usually prevents normal electrical contact between the charging plug and the phone's input jack. With a simple brush, this debris is difficult to pull out, but just right with a needle.

Further, after we pulled out the compressed garbage, we take a small brush in our hand and continue to clean the usb socket of the phone's input from smaller particles of garbage. Do not forget to blow out this garbage with your lips))). After completing such a simple cleaning of the phone, there is a high probability that your device will start charging normally again. Personally, I have several such successful cases when it helped. Although at first there were thoughts that I would have to carry the phone for repair.

If this did not help, the next most common reason for the phone not charging normally is a problem with the electrical contact of the socket itself and the board on which it is soldered. And also it is not uncommon for a wire (inside) to break near the plug coming from the charger. You can solder the wire yourself. We take and cut the end of the plug near the wire extending from it. A break usually occurs in the gap at a distance of about 5 cm. Chip this piece of wire and re-solder the wire to the plug. Well, if the problem is still in the socket, which has lost contact with the board, then only the repair service will help.

Kirill Sobolev

If the hands are golden, then it doesn’t matter where they grow from.

Content

Initially, the mobile was a simple device for making calls. Now it is a multifunctional device, without which a person will not be so comfortable. With careless use, the power socket sometimes breaks. In this case, you should know how to fix the phone charging connector or charge it in another way.

How to fix a phone charging socket by changing position

It is necessary to immediately indicate that it will not be possible to repair your device in this way. A broken power socket will remain so and repair cannot be avoided. This half-measure is necessary in situations where there is no required amount for repairs, but you need to use your mobile phone. Instructions on how to charge the phone if the socket is broken:

1. Connect the charger to the device, plug into the network.
2. Try to wiggle the cord by moving the plug up and down.
3. If the battery cannot be charged because the contact has come loose, doing so may short it out.
4. If the cell phone has detected the charger, try to fix this position. Try placing books or other objects under the wire so that the mobile phone can lie there overnight and the battery is charged.

Before carrying out such a manipulation, make sure that the problem is really in the connector, and not the battery. When used for a long time, they have the ability to stop holding a charge. In this case, you should buy a new battery, and not deal with an allegedly damaged socket. . If the matter is really in the connector, then repair is unlikely to be avoided. Keep in mind that such manipulations with the wire can further loosen the connection point or break it completely.

Replacing the charging connector with a universal "frog"

In a critical situation, when you don’t know how to charge your phone, if the socket is broken, you can use universal charging. Sometimes the device is called a “frog”, it is relatively expensive, so it’s not a fact that it’s better than giving the device for repair. This device has a special groove into which you need to insert the battery removed from the mobile. However, this method has several obvious disadvantages:

• during recharging, the smartphone is turned off, you can not use it until the battery is charged;
• the cost of the "frog" is high and sometimes does not justify the costs;
• among user reviews there are situations when the charger broke the battery.

The charging connector on the phone is broken - we charge directly

If you don't know how to change the charging socket on your phone, you can try recharging the battery by removing the need for the power socket. The method is relatively complex and requires some skills from the field of working with electricity. The bottom line is this:

1. You need to remove the battery from your phone.
2. Cut off the insulation from the charger wire, expose the wires (disconnect from the outlet).
3. Strip the wires, determine where the plus and minus are.
4. Locate the corresponding terminals on the cell phone battery. It is important to observe the polarity of the wires and the device.
5. Fix the wires and plug the plug into the socket.

It is strongly not recommended to use this method if you are not 100% sure of your skills. You should not carry out manipulations when you are alone at home, there must be a person nearby who could help you with a possible electric shock. It should be borne in mind that this connection option is not normal for the battery and can lead to breakdown or premature exhaustion.

How to replace the charging port on your phone

The only proven way to get rid of the problem is to put the matter in the hands of professional workers. Perhaps after being told how much it costs to fix a phone charging jack, you don't want to use any "workarounds". In modern devices, this connector still performs the function of connecting to a computer, transferring data, so its breakdown greatly reduces the functionality of the device. This is a microcircuit that cannot be repaired at home on its own. Phone repair often results in a round sum and you should be prepared for this.

In this case, it is best to contact a certified center. The ideal option would be a branded service point of the same manufacturer as your mobile. They know all the intricacies of the device of their products and will be able to provide qualified assistance to fix the breakdown. Inexperienced or inaccurate workers can aggravate the situation and lead to even greater damage to the device.

Video: how to replace the power connector on the phone

Did you find an error in the text? Select it, press Ctrl + Enter and we'll fix it!

The situation when the battery on a smartphone runs out and there is no way to charge it is critical for many. That is why it is very important to find out why the phone is not charging and choose the best option to fix the problem. The instruction is suitable for all models and brands: iPhone, Alcatel, Asus, Lenovo, Phillips, Prestigio, Sony Xperia, HTC, Samsung, Xiaomi, Umidigi, Leagoo, Doogie, Huawei, HomTom, etc.

Several things are involved in the charging process at once: the charger, consisting of a plug, tip and cord, as well as the battery itself. That is why, if the smartphone does not charge and does not receive energy from a regular or new purchased "Chinese" charger, we check each node separately.

1. Damaged or clogged connector.
2. The cord comes off (backlash) or the plug does not match the socket (for example, micro-USB is not suitable for Type-C and Lightning).
3. Software failures.
4. Fracture wire, "lohmachivanie" wire.
5. Using dubious Chinese "handicrafts" for 20 rubles, the veins in cheap versions are very thin and break from a slight impact.
6. Too long wire, the shorter the length (30 cm is ideal), the less current loss. But again, it all depends on the quality.
7. Battery failure (swollen, overheated, worn out from old age).
8. Burnt power controller or protocol incompatibility.
9. Heavy CPU usage, such as playing a heavy game or watching 4K movies.
10. Non-compliance with temperature regimes. The process of replenishing the battery does not occur at sub-zero temperatures,.
11. They forgot to “peel off” the protective sticker after buying a new gadget.

If the phone charges normally but drains quickly, it is likely that a virus has been infected that is causing problems in the power supply system.

There is another factor - the temporary wear of the battery. The standard battery life is 3 to 5 years (equivalent to 300-500 charge-discharge cycles), after which it begins to discharge a couple of hours after charging, or does not perceive it at all.

Sometimes it shows that the charge level is increasing. But in reality, the battery does not take or does not respond to the supply of energy, and after disconnecting the cable, the voltage drops sharply to zero.

Diagnostics

For self-diagnosis, take the test. The virtual assistant will determine the malfunction and tell you what to do.

We continue the diagnostics >>

Has the USB cable been inspected for kinks or kinks?

We continue the diagnostics >>

Not charging

To understand why the phone does not charge well or the power indicator does not appear on the display, you need to follow a few simple steps:

1. Take a non-native memory and connect to your smartphone.
2. Change the USB cable to a new one (pay attention to the connector, 4 main ones are currently used - USB Type-C, micro-USB, Lightning and outdated mini-USB).
3. The indicator lights up, which means that the problem is a charging malfunction.

If another charger does not work and does not bring the charge level to the end, it is likely that the problem lies in the software, battery or cell phone connector.

First of all, you should carefully clean the nest. If this does not help, it is recommended to take the gadget to the service, because. it will be difficult to fix it yourself.

A faulty power supply - the owner himself can repair it by purchasing the necessary replacement part, but due to the low cost of USB cords, it is more logical to purchase a new one.

How to check the connector

Diagnosing the condition of the USB-cord socket consists in examining it in bright light using a magnifying glass. If it is dirty, clean it with a thin brush dipped in alcohol. Dust and debris create poor conductor contact and interfere with current flow.

What to check:

• The socket does not wobble in the case.
• No contamination observed.
• There is no visible deformation of the module (bent contact groups, geometry changes, etc.).
• Visually, there are no drops of water and moisture.

If this is not the case, you will have to look for the reason in another part.

How to check the battery

The above method showed that the smartphone does not receive energy not as a result of a burned-out memory, but because of a damaged cable. If the cable is plugged in and says it's charging, but the phone isn't charging, it's likely that the battery needs to be replaced.

• The battery is swollen and/or protruding from the case.
• The battery is not fully and slowly charged, no more than up to 60-90 percent, - only the replacement of the module.
• With a working memory, the cell does not take or does not see charging, although the process is underway.
• Download the utility to check the remaining capacity.

So you need to test the battery: just replace it with another analogue and see if the indicator lights up when connected to a power outlet. For Apple technology, this method will not work!

Signs of a virus infection

The main symptom when the software is infected with malware is the lack of indication. Also, it can constantly freeze, and if earlier the battery lasted for two days, then after the virus enters, it will be discharged in 5-12 hours (i.e., for a very long time).

To troubleshoot, you need to check the phone with an antivirus. If infected files are found, they will be deleted automatically, and if this is not possible, you will have to clean the system manually by removing the application itself that contains viruses.

How to charge without a standard charger

In any cell phone store you can find a universal charger suitable for both smartphones and iPhones. The battery can also be any.

In another way, it is called a "frog", and it is very easy to use such a charge:

1. We insert the battery into the latch, the "plus" and "minus" contacts must match.
2. We insert the "frog" into the outlet, leave it to charge for several hours.

Question answer

% stands still is not added

Or the process is only in the off state:

1. There is not enough current in the charger. For example, the charger gives out 250 mAh with the required 1000 mAh.
2. The USB cord is of extremely poor quality and does not pass more than 4.5 volts, which is critical.

Can't charge from computer/laptop via USB

• Most likely there is not enough current, for example, due to artificial restrictions on the computer's motherboard. Or the restrictions are triggered at the software level, you will have to look for new drivers for the USB hub.
• This can happen if the cord is old or “works every other time”. Somewhere in it shorting contacts. Especially true for "shaggy" cables for the iPhone. Basically, buy a new one.
• Another commonplace reason that is relevant for different variations of Type-C is the incompatibility of protocols. Each Type-C has a small chip that is responsible for transmitting data and power. At the same time, there are a lot of standards, for example, some cables can “refuel” full-fledged laptop batteries, while others can only exchange data.
• It happens that the USB connector in laptops is longer than the standard plug from a smartphone, and the hardware simply does not touch.

From the cigarette lighter

If car charging from the cigarette lighter does not work, a similar diagnosis is carried out (see previous sections), because. The principle of supplying energy to the battery is the same everywhere.

From the radio

From the bank

Standard sitation, most often there is not enough output current from PowerBank. Or is it time to buy a new power bank. In the case of Type-c, it is possible that it does not allow charging the battery.

From wireless charging

Not all models support the wireless power transmission function. First, make sure that the manufacturer has included this functionality in your gadget.

If you are sure that wireless transmission is implemented at the hardware level, but there is no charge, you need to check:

• Whether the station is connected offline.
• Does the device move / move from the center of the site.
• Not wearing a thick case or magnetic dock.
• Is a cable plugged in or data is not being transferred to the computer.

If this does not help, check the station itself on another device, if everything works as it should on it, take your device to the workshop. Very similar to a problem with a wireless microcontroller.

Writes moisture detected

There are two options here:

1. The unit has been dropped into water or other liquid (beer, wine, juice, tea, toilet bowl). What to do is written.
2. There was a strong temperature difference, for example, they came from frost to a warm room and condensation formed on the board. Wait a couple of hours and everything will be back to normal.

Low or high battery temperature

The operating temperature of modern batteries is from +3 to 45 degrees Celsius. If these values ​​are exceeded, the controller limits the supply of energy to the batteries. It is necessary to cool / heat the phone.

There was a strong blow or fall

Lithium-ion "products" do not like strong mechanical impact, and can fail with strong shocks and falls. Here only the replacement of the module with a new one.

After a long period of disuse

A deep discharge has occurred - use the "frog" to "push through" and try to revive the battery.

To extend the life of your iPhone or Android smartphone, you need to follow the recommendations:

• Do not let the gadget fall.
• Do not discharge the battery too often (no more than once every 2 months) completely to 100 percent. It is ideal to keep the level between 20% and 80%.
• Do not abuse the use of a low-power universal charger, even a new one.
• Install anti-virus protection on your phone.
• Do not leave the device in the cold or heat (operating temperature from +3 to 45 degrees).

Conclusion

Many owners of smartphones (both on Android and iOs) face the problem of a lack of charge, but for diagnostics it is not necessary to take the phone to a service: just use the instructions to find out the reason.

If the gadget does not charge due to a battery failure or has stopped receiving energy due to the USB connector, it is recommended to contact the wizard. In other cases, it is enough to replace the damaged charger with a new one, ideally with the original one.

Video

In fact, he is the chief editor of the entire site, always in touch with the best authors. Correction and proofreading, his work. An excellent expert in his field. Excellent understanding of the technical nuances of electronics. Occasionally writes and publishes original articles.

• published articles - 15
• readers - 3 179
• online since September 5, 2017

Additionally